thread diameter造句
例句與造句
- fasteners . tolerances for bolts, screws and nuts product grade f fine mechanic . thread diameters from 1 up to 3 mm
緊固件.級螺釘和螺帽公差精密機械.螺紋直徑1到3mm - rod ends, adjustable, single fork and threaded shank with engagement : 1.5 thread diameter-dimensions and loads
嚙合量為1.5螺紋直徑的單叉螺紋柄可調節的連桿端頭.尺寸和負荷 - rod ends, adjustable, double fork and threaded shank with engagement : 1.5 thread diameter-dimensions and loads
嚙合量為1.5螺紋直徑的雙叉螺紋柄可調節的連桿端頭.尺寸和負荷 - aerospace series; rod-ends, adjustable, single fork and threaded shank with engagement : 1, 5 thread diameter; dimensions and loads; german version en 2791 : 1991
航空航天系列.嚙合長度為螺紋直徑1.5倍的螺紋桿和單 - aerospace series; rod-ends, adjustable, double fork and threaded shank with engagement : 1, 5 thread diameter; dimensions and loads; german version en 2792 : 1991
航空航天系列.嚙合長度為螺紋直徑1.5倍的螺紋桿和雙 - It's difficult to find thread diameter in a sentence. 用thread diameter造句挺難的
- screw setting gauges for measuring instruments for iso metric screw threads; setting plug gauges and setting ring gauges from 1 to 100 mm nominal thread diameter
iso米制螺紋測量?jī)x器用螺紋標準量規.螺紋標稱直徑1mm - en 2792 aerospace series . rod ends, adjustable, double fork and threaded shank with engagement : 1, 5 x thread diameter . dimensions and loads
航空航天系列.帶自潤滑油封和螺紋安裝桿的雙包邊可調接頭.螺紋直徑1.5.尺寸和負荷 - en 2791 aerospace series . rod ends, adjustable, single fork and threaded shank with engagement : 1, 5 x thread diameter . dimensions and loads
航空航天系列.帶自潤滑油封和螺紋安裝桿的單包邊可調接頭:螺紋直徑1.5.尺寸和負荷 - aerospace series; rod-ends, adjustable, self-aligning plain bearing with self-lubricating liner and threaded shank, with engagement : 1, 5 thread diameter; dimensions and loads; german version en 2790 : 1991
航空航天系列.嚙合長度為螺紋直徑1.5倍的螺紋桿的帶 - en 2790 aerospace series . rod ends, adjustable, self-aligning plain bearing with self-lubricating liner and threaded shank with engagement : 1, 5 thread diameter . dimensions and loads
航空航天系列.帶自潤滑油封和螺紋安裝桿的球形可調接頭:螺紋直徑1.5.尺寸和負荷 - the seams of the internal threads are eliminated by the reverse rotation while producing few chips ， and uniform threads diameter is achieved even though the hole diameter is uneven
正轉時擠壓出內螺紋，逆轉時切去內徑部的縫隙(有微量碎屑排出)，從而完成加工。下孔徑尺寸即使零亂，也可以做出內徑尺寸均一的螺紋。 - the in-plane equivalent elastic modulus and tensile strength of stitched composite laminates are studied, and it's found that the in-plane equivalent elastic modulus decreases with the increase of stitch density, stitch thread diameter, maximal misalignment angle and the distortion width, and the range is about 5 % . the tensile strength of stitched composite laminate increases with the increase of stitch step and decreases with the stitch space . the
研究結果表明：隨著縫紉密度、縫紉線直徑、最大纖維偏轉角和縫紉變形區寬度的增加，縫紉復合材料層合板面內等效模量逐漸降低，最大降幅一般在5%左右；縫紉復合材料層合板的拉伸強度隨縫紉針距的增加而增大，隨縫紉行距的增加而降低，因此縫紉密度對拉伸強度的影響程度要看具體的縫紉針距和行距。 - because of the winding framework of integrate electromotor motor is very complex and the thread diameter that coiling on it is thick, it's difficult to realize the automatic coiling of the winding . in order to solve this problem, we research and develop a new type coiling equipment, i . e . robot coiling system
針對一體化電機轉子鐵芯復雜，所繞漆包線線徑較粗，難以實現線圈自動繞制，目前全部采用手工繞制的現狀，設計了一種新型的繞線設備??繞線機器人系統。